Average CNC Programmer Salary in Lithuania for 2026

How much does an CNC programmer make in Lithuania?

A typical CNC programmer working in Lithuania brings home around 2,231 EUR a month before tax. Entry-level pay starts near 13,540 EUR, and the top of the ladder reaches roughly 42,320 EUR for the most experienced and specialised people in the role.

The wide gap between low end and top end reflects how much pay can vary inside the same job title. A junior CNC programmer working at a small local employer earns very different money from a senior at a multinational. Skills, employer, city and years in the seat all push the number around. For a cross-country comparison, see the CNC programmer salary in Belgium or Netherlands, both of which pay in the same currency.

How CNC programmer pay ranges in Lithuania

A good way to think about salary in Lithuania is to look at the distribution rather than the headline average. Half of all CNC programmers in Lithuania earn less than 28,660 EUR a year, and the other half earn more. That middle number is the median, and it is usually more useful than the average for answering "is my pay normal here".

Looking at the quartiles fills in the picture. A quarter of earners take home less than 17,760 EUR (the 25th percentile), and a quarter clear 38,180 EUR (the 75th percentile). The middle 50% of CNC programmers sit somewhere inside that band, which is where the typical reader of this page probably lives.

The very lowest reported salaries sit around 13,540 EUR. The highest stretch to 42,320 EUR, though only a small fraction of earners ever reach that level. If you are deciding whether your own offer or current pay is reasonable, work out which of those four bands you would fall into and use that as your reference point.

CNC programmer pay by experience in Lithuania

Years of experience is the single biggest lever on pay for an CNC programmer in Lithuania, ahead of education and almost any other single factor. The longer you have been in the role, the more your employer can trust you to handle complexity, mentor others and act independently, all of which command higher pay. The chart below shows how the typical CNC programmer salary changes as you move through the career ladder.

The single largest jump on the ladder is from 5 - 10 Years to 10 - 15 Years, where pay rises by about 33%. That is the point at which a CNC programmer typically goes from "competent in the role" to "the person other people in the team learn from", and the market pays well for that step.

CNC programmer pay by education in Lithuania

Education sits alongside experience as one of the biggest factors driving CNC programmer pay in Lithuania. Higher qualifications consistently pull higher salaries, but the size of the gap tends to be smallest at junior levels and widens as people move up. Two people in the same role with the same years of experience but different degrees can end up earning very different money once they reach mid-career.

Below is the average CNC programmer salary in Lithuania broken down by the highest level of education a worker has completed.

CNC programmer gender pay gap in Lithuania

The gender pay gap is a stubborn feature of almost every labour market, and Lithuania is no exception. Male CNC programmers in Lithuania earn an average of 26,100 EUR a year, while female CNC programmers earn around 26,080 EUR. That works out to a 0% gap in favour of men, even when comparing people doing the same work.

A pay gap of this size has a real long-term cost. Over a typical thirty-year career it can add up to several years of pay, and it compounds through pensions, retirement contributions and bonus-linked stock. Some of the gap is explained by women being more likely to work part-time, take career breaks, or be steered toward lower-paying specialisations. Some of it is straightforward unequal pay for the same job, which is harder to defend.

Pay raises for an CNC programmer in Lithuania

Most countries hand out at least some kind of pay raise every year, typically when an employee's contract is reviewed or as a cost-of-living adjustment to keep wages roughly in step with inflation. The rhythm and size of those raises varies hugely between industries.

A typical worker doing this role in Lithuania sees a raise of about 9% every 19 months, which works out to roughly 6% on an annual basis. That figure is the typical underlying rate; in years where inflation runs high you can usually expect a bit more, and in flat-economy years a bit less.

Across all jobs in Lithuania, the national average raise is around 8% every 18 months.

By industry

Industries with the highest pay raises in Lithuania:

By experience level

Experienced workers tend to see larger raises. Retaining a senior is cheaper than replacing them, so employers fight harder for them.

CNC programmer bonus rates in Lithuania

Bonuses are the other half of total compensation, and they vary a lot between jobs and industries. Some roles are paid almost entirely in base salary; others lean heavily on bonus structures tied to revenue, project completion or company performance. Whether a job pays a bonus, how big it is, and how often it lands all factor into whether the headline salary is actually a good offer.

Which careers pay bonuses in Lithuania

Revenue-facing roles tend to pay the biggest bonuses. Operational and support roles tend toward smaller, more predictable ones.

CNC programmer: public vs private sector pay

Public-sector pay in Lithuania is about 9% more than private-sector pay for similar work. The private sector typically offers stronger upside and bigger bonuses; the public sector typically offers better benefits and stability.

CNC programmer salary by city in Lithuania

CNC programmer pay is not even across Lithuania. The chart below shows the highest-paying cities in the dataset, followed by the full location table.

Similar jobs to an CNC programmer

Other jobs in the same category as an CNC programmer in Lithuania.

CNC Programmer in Lithuania: FAQs