Average CNC Programmer Salary in Saudi Arabia for 2026

How much does an CNC programmer make in Saudi Arabia?

A typical CNC programmer working in Saudi Arabia brings home around 10,866 SAR a month before tax. Entry-level pay starts near 68,320 SAR, and the top of the ladder reaches roughly 200,000 SAR for the most experienced and specialised people in the role.

The wide gap between low end and top end reflects how much pay can vary inside the same job title. A junior CNC programmer working at a small local employer earns very different money from a senior at a multinational. Skills, employer, city and years in the seat all push the number around.

How CNC programmer pay ranges in Saudi Arabia

A good way to think about salary in Saudi Arabia is to look at the distribution rather than the headline average. Half of all CNC programmers in Saudi Arabia earn less than 125,100 SAR a year, and the other half earn more. That middle number is the median, and it is usually more useful than the average for answering "is my pay normal here".

Looking at the quartiles fills in the picture. A quarter of earners take home less than 86,420 SAR (the 25th percentile), and a quarter clear 152,000 SAR (the 75th percentile). The middle 50% of CNC programmers sit somewhere inside that band, which is where the typical reader of this page probably lives.

The very lowest reported salaries sit around 68,320 SAR. The highest stretch to 200,000 SAR, though only a small fraction of earners ever reach that level. If you are deciding whether your own offer or current pay is reasonable, work out which of those four bands you would fall into and use that as your reference point.

CNC programmer pay by experience in Saudi Arabia

Years of experience is the single biggest lever on pay for an CNC programmer in Saudi Arabia, ahead of education and almost any other single factor. The longer you have been in the role, the more your employer can trust you to handle complexity, mentor others and act independently, all of which command higher pay. The chart below shows how the typical CNC programmer salary changes as you move through the career ladder.

The single largest jump on the ladder is from 2 - 5 Years to 5 - 10 Years, where pay rises by about 42%. That is the point at which a CNC programmer typically goes from "competent in the role" to "the person other people in the team learn from", and the market pays well for that step.

CNC programmer pay by education in Saudi Arabia

Education sits alongside experience as one of the biggest factors driving CNC programmer pay in Saudi Arabia. Higher qualifications consistently pull higher salaries, but the size of the gap tends to be smallest at junior levels and widens as people move up. Two people in the same role with the same years of experience but different degrees can end up earning very different money once they reach mid-career.

Below is the average CNC programmer salary in Saudi Arabia broken down by the highest level of education a worker has completed.

CNC programmer gender pay gap in Saudi Arabia

The gender pay gap is a stubborn feature of almost every labour market, and Saudi Arabia is no exception. Male CNC programmers in Saudi Arabia earn an average of 139,100 SAR a year, while female CNC programmers earn around 119,900 SAR. That works out to a 16% gap in favour of men, even when comparing people doing the same work.

A pay gap of this size has a real long-term cost. Over a typical thirty-year career it can add up to several years of pay, and it compounds through pensions, retirement contributions and bonus-linked stock. Some of the gap is explained by women being more likely to work part-time, take career breaks, or be steered toward lower-paying specialisations. Some of it is straightforward unequal pay for the same job, which is harder to defend.

Pay raises for an CNC programmer in Saudi Arabia

Most countries hand out at least some kind of pay raise every year, typically when an employee's contract is reviewed or as a cost-of-living adjustment to keep wages roughly in step with inflation. The rhythm and size of those raises varies hugely between industries.

A typical worker doing this role in Saudi Arabia sees a raise of about 9% every 18 months, which works out to roughly 6% on an annual basis. That figure is the typical underlying rate; in years where inflation runs high you can usually expect a bit more, and in flat-economy years a bit less.

Across all jobs in Saudi Arabia, the national average raise is around 8% every 17 months.

By industry

Industries with the highest pay raises in Saudi Arabia:

By experience level

Experienced workers tend to see larger raises. Retaining a senior is cheaper than replacing them, so employers fight harder for them.

CNC programmer bonus rates in Saudi Arabia

Bonuses are the other half of total compensation, and they vary a lot between jobs and industries. Some roles are paid almost entirely in base salary; others lean heavily on bonus structures tied to revenue, project completion or company performance. Whether a job pays a bonus, how big it is, and how often it lands all factor into whether the headline salary is actually a good offer.

Which careers pay bonuses in Saudi Arabia

Revenue-facing roles tend to pay the biggest bonuses. Operational and support roles tend toward smaller, more predictable ones.

CNC programmer: public vs private sector pay

Public-sector pay in Saudi Arabia is about 8% more than private-sector pay for similar work. The private sector typically offers stronger upside and bigger bonuses; the public sector typically offers better benefits and stability.

CNC programmer salary by city in Saudi Arabia

CNC programmer pay is not even across Saudi Arabia. The chart below shows the highest-paying cities in the dataset, followed by the full location table.

Similar jobs to an CNC programmer

Other jobs in the same category as an CNC programmer in Saudi Arabia.

CNC Programmer in Saudi Arabia: FAQs